Here in the next paragraph you'll find lots of wonderful points in regards to A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is easily accessible, the project can move rapidly; if you have to open a wall surface to remove the old tub as well as place the brand-new tub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the brand-new one. See to it you have certified yourself for the task and also fit trying it. As opposed to hiring a professional to take over a halfway-completed task, it is better to think about using one before you start. Possibilities are you may need an expert plumber to make tube links.
This article will assist you mount a new tub in your bathroom if you have actually already gotten a new bathtub and do not require to change the plan of your previous water pipelines.
Your devices and also material list ought to comprise the following:
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing taps can be fairly problematic as a result of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, position the bath tub in the required setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest flexible tap connector to the ideal supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the water and also examine all joints and also brand-new pipework for leaks and also tighten them if required. Fill up the bathtub and also examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the tub ought to wait till the tub has actually been utilized at the very least when as this will settle it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making certain that the washing machines remain in place in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind must be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing complications with dampness as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in use. The sealant can break rather very early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on How to Install a Bathtub Yourself? Give feedback down the page. We'd be delighted to see your insights about this article. Hoping to see you back again in the future. For those who liked our blog posting plz don't forget to share it. Thank you so much for your time spent reading it.
Request A Quote